1/2" X 30.125" dimensions

Specifications 0.755" outside diameter 0.375" inside diameter 0.438" length Note: Used for both gas and LP models. Model Note Equipment Information A AV Super A Super A-1 Super AV Super AV-1 B BN C Super C 100 130 140 200 230 240 330 340 404 424 444

Kit contains all parts necessary for major carburetor overhaul. Part Reference Numbers: 50981DA;C510HV Fits Models: H; HV; W4

Model Note Equipment Information B when equipped with an optional Monroe Easy Ride seat BN when equipped with an optional Monroe Easy Ride seat C Super C H HV Super H Super HV M MD Super M Super MDV Super MTA MV Super MV F20 when equipped with an optional Monroe Easy Ride seat F30 when equipped with an optional Monroe Easy Ride seat 200 230 300 350 400 450 460 560 600 650 660

Rubber control valve boot. This will work for leather boot 351753R3. also check FP26476 Fits: Cub, Cub Loboy (-(WILL NOT FIT 154, 184, 185)-), Super A, Super A-1, Super AV, Super AV-1, Super C, 100, 130, 140, 200; Replaces: 364832R1, 364832R2

Rubber control valve boot. This will work for leather boot 351753R3.

DELUXE UPHOLSTERED SEAT PAN --- ATTACHES W/ FOUR BOLTS --- USA MADE --- RED / WHITE SEAT PAN IS UPHOLSTERED IN A VINYL COVER --- International Applications: CUB, CUB LOBOY, SUPER C, C, 200, 230, 240, H (SN 15698 & UP), HV, SUPER H, SUPER HV, M (SN 9287 & UP), MD, MV, SUPER M, SUPER MV, MTA, 300, 340, 350, F- 400, F- 450, 460, 600, 650 --- Replacement Part #: IH 357518R91, 351880R92, 351925R93

DELUXE UPHOLSTERED SEAT PAN --- ATTACHES W/ FOUR BOLTS --- USA MADE --- SILVER SEAT PAN IS UPHOLSTERED IN A NYLON BASKET WEAVE COVER FOR ORIGINAL LOOK --- HAS BRASS RING DRAIN HOLE --- International Applications: CUB, CUB LOBOY, SUPER C, C, 200, 230, 240, H (SN 15698 & UP), HV, SUPER H, SUPER HV, M (SN 9287 & UP), MD, MV, SUPER M, SUPER MV, MTA, 300, 340, 350, F- 400, F- 450, 460, 600, 650 --- Replacement Part #: 357518R91

FLAT LEAF SEAT SPRING - Left hand- International Farmall A, AV, A-I, AV-I, SUPER A, B, BN, 100, 130, 140; ALSO FITS IH 300, 350, 460 UTILITIES W/ LOW-STYLE SEAT, 50586DB

FLAT LEAF SEAT SPRING Right Hand International - Farmall A, AV, A-I, AV-I, SUPER A, B, BN, 100, 130, 140; ALSO FITS IH 300, 350, 460 UTILITIES W/ LOW-STYLE SEAT - 50587DB

Flexible Fuel Line Length is 31" from end of fitting to end of fitting. Fits International Farmall H, M, Super H, Super M, 300, 350, 400 Complete with fittings

Cub Cadet Original uses this sediment bowl with female pipe thread on the 7hp Kohler motors.

This rubber boot goes on the hydraulic block piston and is the smaller of the 2 boots on the hydraulic block. This boot can be used for leather boot 352005R3. Fits: C, Cub, Cub Loboy (-(WILL NOT FIT 154, 184, 185)-), Super A, Super A-1, Super AV, Super AV-1, Super C, 100, 130, 140, 200; Replaces: 364833R1, 364833R2 Made in the USA

For H and HV. This manual is a New reproduction of the original owner's manual that came with the tractor. 111 pages.

Adapts an Farmall 1-1/8 inch PTO shaft to a 1-3/8 shaft. Using this adapter you can have your old Farmall run a new mower, auger, seeder, sprayer, or other implement. The adapter comes with a roll pin to attach it to the pto shaft, and is machined for use with quick release implements.

B BN

DELUXE UPHOLSTERED SEAT PAN. ATTACHES W/ FOUR BOLTS, USA MADE, SILVER SEAT PAN IS UPHOLSTERED IN A NYLON BASKET WEAVE COVER FOR ORIGINAL LOOK. International Farmall CUB, CUB LOBOY, SUPER C, C, 200, 230, 240, H (SN 15698 & UP), HV, SUPER H, SUPER HV, M (SN 9287

SEAT SPRING COIL, USA MADE, International Farmall C, H, HV, M, MD, MV, SUPER C, LATE F20 & F30 (BOTH W/ MONROE EASY-RIDE SEATS); SUPER H, SUPER HV, SUPER M, SUPER MV, SUPER MDV, SUPER MTA, 200, 230, 300, 350, 400, 450, 460, 560, 600, 650, 660

SEAT SPRING IH International C, H, HV, M, MD, MV, MDV, Super C, Super H, Super HV, Super M, Super MD, Super MTA, 200, 230, 240, 300, 350, 400, 450, 460, 560, 660 # Replaces OEM number 354670R2 REPLACES OEM PART NO. 354670R2. IH H, M, HV, MD, C, SUPER C, SUPERM, SUPER MTA, SUPER H, SUPER HV, 200, 230, 300, 350, 400, 450, W400, W450, 600, 650, 460, 560 & 660.

SEAT SUPPORT BRACKET - LEFT --- International Applications: A, AV, SUPER A, SUPER AV, SUPER A1, SUPER AV1, B, BN, 100, 130, 140 --- Replacement Part #: 51181D, 35007R2

SEAT SUPPORT BRACKET - RIGHT --- International Applications: A, AV, SUPER A, SUPER AV, SUPER A1, SUPER AV1, B, BN, 100, 130, 140 --- Replacement Part #: 51182D

UPHOLSTERED FLIP-BACK SEAT -SILVER FLIP-BACK SEAT IS UPHOLSTERED IN NYLON BASKET WEAVE COVER FOR ORIGINAL LOOK - USA MADE - International Farmall H, HV, W4, O4, OS4, I4, M, MD, MV, W6, SUPER W6, WD6, SUPER WD6, O6, I6, ID6, W9, WD9, WR9, WDR9, I9, ID9 -IH Part #: IH: 49498DD, 49498DE

Fits your Farmall with 4 bolts. Fits Farmall Cub, Farmall C, 200, 230, 240, H (Sn15698 & up), HV, Super H, SuperHV, M (SN9287& up) MD, MV, Super M, Super MV, MTA, 300, 340, 350, F-400, 450, 460, 600, 650.

17-1/2" wide 14" front-to-back 3" tall 18 hole Steel Chrome powder coat paint

1066 International Harvester Hood Decal Kit Fits Models: 1066 TRACTOR

17-1/2" wide 14" front-to-back 3" tall 18 hole Steel

Front Axle pin - 4-9/16" LONG, 1-3/16" DIAMETER. -International Applications: 240, 404, 424, 444, 2404, 2424, 2444, WILL ALSO FIT 330, 340

17-1/2" wide 14" front-to-back 3" tall 18 hole Steel

Model Note Equipment Information I4 H HV I9 ID9 M MD MDV MV O4 O6 OS4 OS6 Super W4 W4 Super W6TA W6 W9 WD6 Super WD9 WD9 WDR9

Coil Seat Spring for "H & HV UP TO SN# 15697", "M, MD, MV UP TO SN#9286", I4, W4, O4, OS4, SUPER W4, I6, W6, WD6, O6, OS6, "SUPER W6TA UP TO SN#9084", W9, WD9, SUPER WD9. DIMENSIONS: 2-1/4" O.D. X 4-3/4" TALL.

This is the heavy spring for the channel type seat mount used in Farmall H and M tractors.

1.128" O.D. 0.995" I.D. 1.50" overall length 4 used per tractor Fits both adjustable and nonadjustable front axles

Specifications 1.814" outside diameter 1.677" inside diameter 2.000" overall length 4 used per tractor Sold individually Model Note Equipment Information H with tie rods behind the axle Super H M with tie rods behind the axle MD with tie rods behind the axle Super M Super MD MTA Super MTA Super MTA Diesel Hydro 186 Hydro 70 Hydro 84 Hydro 86 300 Farmall Rowcrop 300 Utility 330 with non adjustable axle 340 with non adjustable axle 350 Farmall Rowcrop 350 Utility 400 Farmall Rowcrop W400 404 with non adjustable axle 450 Farmall Rowcrop W450 454 with straight center axle 460 484 with straight center axle 504 544 Farmall Rowcrop 544 Utility 560 574 584 606 656 Farmall Rowcrop 656 Utility 660 664 666 674 684 686 706 756 766 784 785 786 806 826 856 884 886 966 986 1026 1066 1086 1206 1256 1456 1466 1468 1566 1568 1586 2444 with non adjustable axle 3088 3288 3488 3688 5088 with round tube center axle 5288 with round tube center axle 5488 with round tube center axle

Specifications 1.580" O.D. 1.458" I.D. 1.508" overall length 4 used per tractor Sold individually Model Note Equipment Information 240 with regular axle Farmall 240 with regular axle International 330 with regular axle International 340 with regular axle Farmall 340 with regular axle International 404 with regular axle Farmall 404 with regular axle International 424 with regular axle 444 with regular axle 454 with swept back axle 464 with swept back axle 484 with swept back axle 504 with regular axle Farmall

Specifications 1.237" I.D. 1.415" O.D. 1.760" overall length 0.089" thick 4 used per tractor Model Note Equipment Information A AV Super A Super A-1 Super AV Super AV-1 C Super C 100 130 140 200 230

Specifications 2.875" Long 1.495" O.D. 1.353" I.D

Specifications 2.463" O.D. 1.450" I.D. 0.621" thick 2 used per tractor Note: Sold Individually. 240 240 Farmall 330 with adjustable axle 340 Farmall 340 with adjustable axle 404 Farmall 404 with adjustable axle 424 with adjustable axle 444 with adjustable axle 454 with swept back axle 464 484 with swept back axle using 1-7/16" Dia. Spindle 504 Farmall

Specifications 1.755" inside diameter 2.685" outside diameter 0.694" wide H with tie rods behind the axle Following serviceable but smaller O.D. Super H Following serviceable but smaller O.D. M Following serviceable but smaller O.D. MD Following serviceable but smaller O.D. Super M Following serviceable but smaller O.D. Super MD Following serviceable but smaller O.D. MTA Following serviceable but smaller O.D. Super MTA Following serviceable but smaller O.D. Super MTA Diesel Following serviceable but smaller O.D. Hydro 100 Following with factory IH wide front axle Hydro 186 Following with factory IH wide front axle Hydro 70 Following with factory IH wide front axle Hydro 84 Following with factory IH wide front axle Hydro 86 Following with factory IH wide front axle 300 Following serviceable but smaller O.D. 330 Following serviceable but smaller O.D. 340 with non adjustable axle Following serviceable but smaller O.D. 350 Following serviceable but smaller O.D. 400 Serviceable but smaller O.D. Farmall Rowcrop 404 with non adjustable axle Following with factory IH wide front axle 424 with non adjustable axle Following with factory IH wide front axle 444 with non adjustable axle Following with factory IH wide front axle 450 Serviceable but smaller O.D. Farmall Rowcrop 454 with straight center axle Following with factory IH wide front axle 460 Following with factory IH wide front axle 484 with straight center axle & swept axle when using 1-11/16" Dia. spindle Following with factory IH wide front axle 504 Following with factory IH wide front axle 544 Following with factory IH wide front axle 560 Following with factory IH wide front axle 574 Following with factory IH wide front axle 584 Following with factory IH wide front axle 606 Following with factory IH wide front axle 656 Following with factory IH wide front axle 660 Following serviceable but smaller O.D. 664 Following with factory IH wide front axle 666 Following with factory IH wide front axle 674 Following with factory IH wide front axle 684 Following with factory IH wide front axle 686 Following with factory IH wide front axle 706 Following with factory IH wide front axle 756 Following with factory IH wide front axle 766 Following with factory IH wide front axle 784 Following with factory IH wide front axle 785 Following with factory IH wide front axle 786 Following with factory IH wide front axle 806 Following with factory IH wide front axle 826 Following with factory IH wide front axle 856 Following with factory IH wide front axle 884 Following with factory IH wide front axle 886 Following with factory IH wide front axle 966 Following with factory IH wide front axle 986 Following with factory IH wide front axle 1026 Following with factory IH wide front axle 1066 Following with factory IH wide front axle 1086 Following with factory IH wide front axle 1206 Following with factory IH wide front axle 1256 Following with factory IH wide front axle 1456 Following with factory IH wide front axle 1466 Following with factory IH wide front axle 1468 Following with factory IH wide front axle 1566 Following with factory IH wide front axle 1568 Following with factory IH wide front axle 1586 Following with factory IH wide front axle 3088 Following with factory IH wide front axle 3288 Following with factory IH wide front axle 3488 Following with factory IH wide front axle 3688 Following with factory IH wide front axle 5088 with round tube center axle Following with factory IH wide front axle 5288 with round tube center axle Following with factory IH wide front axle 5488 with round tube center axle Following with factory IH wide front axle

2" O.D. 6.925" long

Specifications 3.250" outside diameter 2.625" inside diameter 0.375" thick 2 used per tractor; sold individually Note: For applications with the factory IH wide front axle. H with tie rods behind the axle Super H M with tie rods behind the axle MD with tie rods behind the axle Super M Super MD MTA Super MTA Super MTA Diesel O6 ODS6 OS6 Super W6 Super W6TA W6 Super WD6 WD6 300 300 Farmall 330 with non adjustable axle 340 350 350 Farmall 400 400 Farmall W400 450 Farmall W450 660

Specifications 2.844" outside diameter 2.375" inside diameter 0.188" thick 2 used per tractor Sold Individually Hydro 100 Hydro 186 Hydro 70 Hydro 84 Hydro 86 404 with non adjustable axle 424 with non adjustable axle 444 with non adjustable axle 454 460 484 504 544 544 Farmall 560 574 with swept back axle 584 606 656 664 666 674 684 686 706 756 766 784 785 786 806 826 856 884 886 966 986 1026 1066 1206 1256 1456 1466 1468 1486 1566 1586 3088 3288 3488 3688 5088 with round tube center axle 5288 with round tube center axle 5488

Specifications 2.563" outside diameter 2.188" inside diameter 0.250" thick 2 used per tractor; sold individually 240 240 Farmall 330 340 340 Farmall 404 404 Farmall 424 444 504 Farmall

Specifications Gas / LP For replacement oil filter order IHS6018 Model Note Equipment Information A gas or LP without hydraulics I4 gas or LP Super A Gas / LP Super A-1 Gas / LP Super AV Gas / LP Super AV-1 Gas / LP B gas or LP BN gas or LP C Gas / LP Super C Gas / LP H gas or LP HV gas or LP Super H gas or LP Super HV gas or LP M gas or LP MTA gas or LP Super MTA gas or LP MV gas or LP O4 gas or LP O6 gas or LP OS4 gas or LP OS6 gas or LP T6 gas or LP Super W4 gas or LP W4 gas or LP Super W6 gas or LP Super W6TA gas or LP W6 gas or LP 100 Gas / LP 130 Gas / LP 140 Gas / LP 200 Gas / LP 230 Gas / LP 240 Gas / LP 300 gas or LP 330 Gas / LP 340 Gas / LP 350 gas or LP 400 gas or LP W400 gas or LP 404 Gas / LP 424 Gas / LP 444 Gas / LP 450 gas or LP W450 gas or LP 504 Gas / LP

Our complete valve kit fits the 123 CI inline 4 motor used in Farmall Super C, 100, 130, 140 tractors.***WE NEED A LOT OF INFO ABOUT YOUR ENGINE TO GET YOU THE RIGHT PARTS*** Includes the following: 4 X 123 CI GAS Intake Valve 4 X 123 CI GAS Exhaust Valve 16 X 123 CI GAS Valve Keeper 8 X 123 CI GAS Valve Stem Seal 8 X 123 CI GAS Valve Guide 4 X 123 CI GAS Valve Spring 4 X 123 CI GAS Valve Spring

Fuel Strainer

Specifications 1.245" inside diameter 1.375" outside diameter 1.486" long 2 used per tractor Sold individually This bushing has a superior dimpled brass inner design to retain grease. No need for an external grease hole. Note: Must be honed or reamed to size when installed. BMD as a reverse idler gear bushing H Following as a WIDE FRONT axle pivot pin bushing for factory adjustable wide front axle and tie rods behind the axle Super H Following as a WIDE FRONT axle pivot pin bushing for factory adjustable wide front axle and tie rods behind the axle M as a reverse idler gear bushing M Following as a WIDE FRONT axle pivot pin bushing for factory adjustable wide front axle and tie rods behind the axle MD as a reverse idler gear bushing MD Following as a WIDE FRONT axle pivot pin bushing for factory adjustable wide front axle and tie rods behind the axle Super M as a reverse idler gear bushing Super M Following as a WIDE FRONT axle pivot pin bushing for factory adjustable wide front axle and tie rods behind the axle Super MD Following as a WIDE FRONT axle pivot pin bushing for factory adjustable wide front axle and tie rods behind the axle Super MDV as a reverse idler gear bushing MDV as a reverse idler gear bushing Super MDV-TA as a reverse idler gear bushing MTA as a reverse idler gear bushing MTA Following as a WIDE FRONT axle pivot pin bushing for factory adjustable wide front axle and tie rods behind the axle Super MTA as a reverse idler gear bushing Super MTA Following as a WIDE FRONT axle pivot pin bushing for factory adjustable wide front axle and tie rods behind the axle MV as a reverse idler gear bushing Super MV as a reverse idler gear bushing Super MVTA as a reverse idler gear bushing O6 as a reverse idler gear bushing ODS6 as a reverse idler gear bushing Super W6 as a reverse idler gear bushing W6 as a reverse idler gear bushing W6TA as a reverse idler gear bushing Super WD6 as a reverse idler gear bushing WD6 as a reverse idler gear bushing Hydro 70 Following as a WIDE FRONT axle pivot pin bushing for factory adjustable wide front axle and tie rods behind the axle 400 as a reverse idler gear bushing 400 Following as a WIDE FRONT axle pivot pin bushing for factory adjustable wide front axle and tie rods behind the axle W400 as a reverse idler gear bushing W400 Following as a WIDE FRONT axle pivot pin bushing for factory adjustable wide front axle and tie rods behind the axle 450 as a reverse idler gear bushing 450 Following as a WIDE FRONT axle pivot pin bushing for factory adjustable wide front axle and tie rods behind the axle B-450 as a reverse idler gear bushing W450 as a reverse idler gear bushing W450 Following as a WIDE FRONT axle pivot pin bushing for factory adjustable wide front axle and tie rods behind the axle 560 as a reverse idler gear bushing 660 as a reverse idler gear bushing 660 Following as a WIDE FRONT axle pivot pin bushing for factory adjustable wide front axle and tie rods behind the axle 666 Following as a WIDE FRONT axle pivot pin bushing for factory adjustable wide front axle and tie rods behind the axle 1026 Following as a WIDE FRONT axle pivot pin bushing for factory adjustable wide front axle and tie rods behind the axle 1256

DUST BOOT --- UNIVERSAL --- BASE X HEIGHT X HOLE I.D. --- 1.200 X .475 X .500 --- International Applications: IH MODELS

Specifications 3/4" - 16 NC thread 4-3/4" overall length Yellow zinc plating 4 used per tractor Note: The nuts are not included with this bolt. Hydro 84 Fits the following extensions with vertical holes (not horizontal) 454 Fits the following extensions with vertical holes (not horizontal) 484 Fits the following extensions with vertical holes (not horizontal) 574 Fits the following extensions with vertical holes (not horizontal) 584 Fits the following extensions with vertical holes (not horizontal) 674 Fits the following extensions with vertical holes (not horizontal) 684 Fits the following extensions with vertical holes (not horizontal) 784 Fits the following extensions with vertical holes (not horizontal) 884

This fits M, MD, Super M, 400, 450, 544, 560, 656, 666, 686, 706, 756, 806, 826, 856, 1206, 1256, Hydro 70.

Specifications 1.00" long 1.134" outside diameter 1.012" inside diameter Fits Models: 1822 Cotton Picker Hydro 100 Hydro 186 766 786 886 966 986 1066 1086 1466 1468 1566 1568 1586 3088 3288 3688 5088 5288 5488

Specifications 0.622" Long 1.510" I.D. 1.625" O.D. Fits Models: 454 with standard axle 484 with standard axle 544 574 584 with standard axle 674 with standard axle 684 with standard axle 784 with standard axle 785 with standard axle 884 with standard axle

UNIVERSAL TIE ROD BOOT --- BASE x HEIGHT x HOLE I.D. --- 1.675 X .900 X .625 --- International Applications: LATE H, SUPER H, M, MD, SUPER M, SUPER MD, MTA, SUPER MTA, 300 ROWCROP, 350 ROWCROP, 400, 450, 460, 544, 560, 656, 666, 686, 706, 756, 766, 786, 806, 826, 856, 886, 966, 1026, 1066, 1086, 1206, 1256, 1456, 1466, 1468, 1486, 1566, 1568, 1586, HYDRO 70, HYD --- Replacement Part #: CNH: 87538419, IH: 358900R1, 359982R1, 387280R1

UNIVERSAL TIE ROD BOOT --- BASE x HEIGHT x HOLE I.D. --- 1.575 BASE X .600 TALL X .650 HOLE --- International Applications: IH MODELS

UNIVERSAL TIE ROD BOOT --- BASE x HEIGHT x HOLE I.D. --- 1.800 X .765 X .740 --- International Applications: IH MODELS

UNIVERSAL TIE ROD BOOT --- BASE x HEIGHT x HOLE I.D. --- 1.300 X .965 X .500 --- International Applications: IH MODELS

WIDE FRONT AXLE MOLDED RUBBER BUMPER --- SOLD INDIVIDUALLY --- International Applications: FARMALL C, SUPER C, 200, 230 --- Replacement Part #: IH: 352482R1

NEW-STYLE KNOB (FOR ROTARY LIGHT SWITCHES) --- FOR ROTARY LIGHT SWITCHES --- ARROW DESIGN --- OEM MANUFACTURE --- International Applications: CUB, CUB LOBOY, A, AV, SUPER A, SUPER AV, SUPER AV1, BN, C, SUPER C, H, HV, SUPER H, SUPER HV, M, MD, MV, MDV, SUPER M, SUPER MD, SUPER MV, SUPER MDV, MTA, I4, I6, ID6, I9, ID9, O4, OS4, O6, OS6, ODS6, W4, W6, WD6, W9, WD9, WR9, WDR9, WR9S, SUPER WD9, SUP

Brake band for Farmall H, & HV

Specifications 0.625" O.D. 5.488" overall length Clear zinc plated Note: 2 used per tractor. Sold individually. Exact of original. 300

BRAKE & CLUTCH PEDAL RETURN SPRING. International A, AV, B, BN, Super A, Super AV, 100, 130, 140

This is the 2 hole mount starter for a Farmall 354B tractor and is what is recommended by supplier. NO RETURNS

push button starter switch

Specifications Note: This switch is designed with an internal "Capacitor" a device that stores electrical energy to run the Switch. 1.424" deep 2.752" tall 2.152" wide 12-volt 6 Spade Terminals (inputs) Terminal one: To (B ) Headlamp Switch Terminal two: To (B ) Battery Terminal three: Left Turn Lamp Terminal four: Right Turn Lamp Terminal five: Right Indicator Terminal six: Left Indicator Other Application Info Also fits the following models - AGCO Windrower: 9330 9340 Agcostar: 8360 8425 Allis Chalmers: 9130 9150 9170 9190 9435 9455 9630 9635 9650 9655 9670 9675 9690 9695 9815 Case IH Combine: 1620 1640 1644 1660 1666 1670 1680 1688 Case IH Sprayer: SPX3310 3150 3185 3210 Challenger: SP80 windrower SP85 windrower SP110 windrower SP115B windrower SP165 windrower SP185B windrower Hesston Windrower: 8110 8110S 8250 8250S 8400 8450 8500 9230 9240 9260 9265 Gleaner Combine: C62 R42 R52 R62 R72 John Deere: 4400 4500 5075 John Deere Harvester: 9960 9965 9970 9976 Massey Ferguson: 4800 4840 4880 4900 Massey Ferguson Combine: 8560 8680 8780 9720 Massey Ferguson Windrower: 220XL 5140 5240 5260 9225 New Idea: 709 uni-power unit 800 uni-power unit 801uni-power unit 802 uni-power unit 803A uni-power unit 5830 windrower 5830X windrower 5850 windrower 8700 combine 8900 combine 8920 combine 9700 combine 9720 combine White Combine: 2500 2600 8570 8590 8600 8700 8800 8900 8920 9700 9720 Model Note Equipment Information Hydro 186 Hydro 84 Hydro 86 484 584 666 684 686 786 884 886 986 1086 1486 1586 3588 3788

0.020" Shim Thickness 1.813" center I/D 3.00" center to center mounting holes

Soft and cozy grey knit beanie. Adorned with a pink International Harvester label and a metal IH emblem, just a splash of IH greatness!

Service manuals. Whenever we bring in a new model to restore we rely heavily on these books to fully understand the parts assemblies and service procedures. Buy the kit and save up to 30% over the same items priced individually. International did not make a service manual for the Super A. They used the A service manual and a hydraulic manual. So you will end up with 4 manuals, operators, parts, service and hydraulic.

OUTER TIE ROD END, NOTCHED - 2 DIFFERENT ONES - CHECK DIMENSIONS BEFORE ORDERING. -16" END TO GREASE ZERK -0.750 DIA ROD - 1/2" DIAMETER THREAD - STUD TAPER=.560 TO .630 -International Farmall LATE SUPER A (SN 318310 & UP), SUPER AV (SN 318310 & UP), C, SUPER C, 100, 130, 200, 230, 385, SOME 454, 485, 574, 585, 595, 674, 784, 884, 885, 495, 695 SWEPT BACK, 464, 484 SWEPT BACK WITH 44-72" AXLE OR 48-80" AXLE - Part 65077C91, 360412R11

COMPLETE TIE ROD ASSEMBLY --- International Applications: FOLLOWING FARMALL ROWCROP TRACTORS WITH TIE RODS BEHIND THE CENTER AXLE: LATE H, SUPER H, LATE M, LATE MD, SUPER M, SUPER MD, MTA, SUPER MTA, SUPER MTA DSL, F300, F350, F400, F450, F460, F544, F560, F656, 666, 686, 706, 756, 766, 786, 806, 826, 856, 886, --- Replacement Part #: ASSEMBLY: 358979R91, 359569R91, INDIVIDUAL PARTS: 383917R1, 359984R92, 384006R92

ECONOMY CHAR-LYNN STEERING COUPLER (FOR TRACTORS WITH U-JOINT) --- USE ONLY IF YOU HAVE A UNIVERSAL JOINT AT ONE END OF EXISTING STEERING SHAFT --- International Applications: IH MODELS

Specifications 3-1/4" from cylinder body to trunnion The block is made for a straight pin. Early production cylinder type FITS MODELS: Hydro 100 up to SN: 12694 Hydro 100 up to SN: 8020 766 up to SN: 7175 886 up to SN: 11559 966 up to SN: 8056 986 up to SN: 13974 1066 up to SN: 8313 1086 up to SN: 21426 1466 up to SN: 7725 1468 1486 up to SN: 12425 1566 up to SN: 13608 1568

14" overall length 7-1/2" cylinder body length 2.885" cylinder body O.D. 3/4" - 16 UNF male end 9/16" - 18 UNF female end

Specifications. 63864C93 2-1/4" from cylinder body to trunnion 8" full rod length 11.5" body length 2.75" cylinder diameter 1" rod diameter 7/8"-14 Threaded stub shaft on RH side Late production cylinder type Hydro 100 SN: 12695 & up 766 SN: 7176

MOUNTING BRACKET --- FOR TORQUE GENERATOR --- International Applications: M, SUPER M, MTA

OUTER TIE ROD END --- 15 3/4" LONG, 0.920 DIAMETER, 6 NOTCHES --- International Applications: LATE H, SUPER H, M, MD, SUPER M, SUPER MD, MTA, SUPER MTA, 300 ROWCROP, 350 ROWCROP, 400, 450, 460, 544, 560, 656, 666, 686, 706, 756, 766, 786, 806, 826, 856, 886, 966, 1026, 1066, 1086, 1206, 1256, 1456, 1466, 1468, 1486, 1566, 1568, 1586, HYDRO 70, HYD --- Replacement Part #: IH: 359984R93

Kit works to increase fuel economy, horsepower, and plug life. Easy to install kit has no moving parts to wear out, and replaces pitted and corroded point sets. Kit does not include distributor. For all years of the 6 Cyl. Windrower 4000 (C232, 258 engine) and it uses the Delco Distributor 1110523, 528.

PORT BLOCK --- NEEDED IF ONLY THE TORQUE GENERATOR IHS554 OR IHS555 IS PURCHASED --- International Applications: H, HV, SUPER H, SUPER HV, M, MD, MV, MDV, SUPER M, SUPER MD, SUPER MV, SUPER MDV, MTA

POWER STEERING PRIORITY FLOW CONTROL VALVE --- ELIMINATES BELT DRIVEN PUMP, PULLEYS & BRACKETS. ENABLES YOU TO USE YOUR LIVE HYDRAULIC PUMP TO OPERATE THE POWER STEERING. --- MUST BE USED W/ LIVE HYD. --- 3/4" INLET & RETURN --- 1/2" PRESSURE PORT -- PRE SET AT 1500 PSI, ADJUST TO YOUR APPLICA --- International Applications: H, SUPER H, HV, SUPER HV, M, SUPER M, MD, MTA, MV, MDV, SUPER MV, SUPER MDV, W4, W6, W9, WD6, SUPER W6, SUPER W4, SUPER W6, SUPER W9, WR9, WD9, SUPER W6TA, SUPER W6TA DSL, SUPER WDR9, 300, 350, 400, 450

SLIP FIT COUPLER (FOR TRACTORS THAT NEED A U-JOINT) --- WHEN EQUIPPED WITH CHAR-LYNN ADD-ON POWER STEERING -- USE THIS COUPLER IF A UNIVERSAL JOINT IS NEEDED ON THE STEERING SHAFT --- International Applications: IH MODELS

Specifications 10 piece kit. Includes: (1) Body Gasket 371543R1 (2) Back up washers 355202R1 (sub for 368635R1) (2) O-rings 86553262 (sub for 253070R1) (2) O-rings 364879R1 (2) O-rings 14453280 (sub for 371544R1) (1) O-ring 371545R1 340 all using Thompson pump #''s 370924R91, 370924R92, 378865R91, 381115R91, C768-35HP, FR922100 460 all using Thompson pump #''s 370924R91, 370924R92, 378865R91, 381115R91, C768-35HP, FR922100 504 all using Thompson pump #''s 370924R91, 370924R92, 378865R91, 381115R91, C768-35HP, FR922100 560 all using Thompson pump #''s 370924R91, 370924R92, 378865R91, 381115R91, C768-35HP, FR922100 606 all using Thompson pump #''s 370924R91, 370924R92, 378865R91, 381115R91, C768-35HP, FR922100 656 F656 up to SN: 13011 all using Thompson pump #''s 370924R91, 370924R92, 378865R91, 381115R91, C768-35HP, FR922100 826 all using Thompson pump #''s 370924R91, 370924R92, 378865R91, 381115R91, C768-35HP, FR922100 1026

TIE ROD BOOT --- 1.500 X .735 X .550 --- International Applications: Cub, Cub LOBOY, Super A, Super AV, C, Super C, 100, 130, 140, 200, 230, 240, F340, F404, 424, 444, 454 w/ swept back axles, 464 w/ swept back axles, 484 w/ swept back axles --- Replacement Part #: IH 358209R1

Assembly includes seat and set screw. The overall length is 2.752" and has 1/2" - 20 NF thread. Two (2) used per tractor, sold individually. NOTE: Will not fit 154, 184, 185.

Includes Grease Zerk, Cotter pin, Threaded Ball retainer and inner ball pad. Fits International: A, AV, B, BN, C, SUPER C, SUPER A (UP TO SN 3318309), SUPER AV (UP TO SN 3318309)

INNER THREADED TIE ROD END - FITS MODELS LISTED WITH AUTOMOTIVE TYPE TIE ROD ENDS. 3.062" END TO GREASE ZERK. 11/16 X 18 RH THREAD -International Farmall LATE SUPER A (SN 318310 & UP), SUPER AV (SN 318310 & UP), C, SUPER C, 100, 130, 200, 230, 385, 2424, 424, SOME 454, SOME 485, 464 W/ SWEPT BACK AXLE. - 356540R91

Specifications 16" overall length 0.750" diameter 7 notches 0.562" thread size taper 0.620" to 0.700" 454 following with swept back front axle 484 following with swept back front axle 574 following with swept back front axle 584 following with swept back front axle 674 following with swept back front axle

1/2" - 20 NF thread. Two (2) used per tractor, sold individually.

Specifications Two (2) used per tractor, sold individually. 14 3/4" Length, Will not fit 154, 184, 185. Measure length before ordering. CUB LO BOY

Specifications 2 used per tractor Sold individually 13-5/8" overall length CUB LO BOY

Specifications Measure length before ordering. The overall length is 18-7/16" and has 1/2" - 20 NF thread. Two (2) used per tractor, sold individually. Will not fit 154, 184, 185. CUB LO BOY

Specifications Measure length before ordering. The overall length is 17-3/8" and has 1/2" - 20 NF thread. Two (2) used per tractor, sold individually. Will not fit 154, 184, 185. CUB LO BOY

TORQUE GENERATOR --- HEAVY DUTY IF ONLY USING THIS PIECE, ALSO NEED PORT BLOCK, IHS673 FOR WHEN A FRONT LOADER IS USED TORQUE OUTPUT AT 1000 PSI = 1100 IN LBS RATED OPERATING PRESSURE = 1000 PSI MAX. OPERATING SPEED AT 3 GPM = 65 RPM RECOMMENDED FLUID INPUT = 3 TO 4 GPM 7 --- International Applications: H, HV, SUPER H, SUPER HV, M, MD, MV, MDV, SUPER M, SUPER MD, SUPER MV, SUPER MDV, MTA & OTHER MODELS USING 7/8"" DIAMETER STEERING SHAFTS

Oil filter for Cub, Cub Lo-Boy, Cub Lo-Boy 154, 185, 184. This filter was also used in the Palmer M60 marine engine.

3.765" free length 0.735" O.D. 0.087" wire diameter

Red handle is a removable key so you can use it like a key. If you have a slow electrical leak, you can keep the battery fresh with this kill switch. Master Battery Isolator Switch 2 Position On-Off Detachable Key Capacity of 500 Amps 12v

If you are having problems with your tractor being reliable, this is just the product for you. Keeps battery terminals corrosion free. Seals high energy Ignition system wiring. prevents voltage leakage, use it on your spark plug boots to prevent voltage leakage. Made in the USA

This will water proof your switch. Made of rubber and has a brass threaded ring that screws onto your existing switch. Has a lot of stretch so will fit on most any toggle switch.

Great switch for lighting or anything that draws a lot of juice. This switch has 4 poles. Two separate incoming and two separate outgoing. Very Heavy duty switch. 20 amp 125 volt, two position On-Off.

This switch is ON-OFF-ON 12 volt 15 Amp. Medium duty for most anything you would want to switch.

RADIATOR HOSE (UPPER) --- 2" I.D. X 2-5/8" I.D. --- International Applications: 140, 240, 404, 424 GAS, 444 GAS --- Replacement Part #: IH: 369397R1 140 240 404 424 Gas 444